July 31, 2008

Race Studio 2.30.06

It seems the updater department of our counterparts in Italy have been busy with updates before their summer vacation they call "August." Race Studio 2 reaches version 2.30.06, amongst other improvements, a small bug was found with 2.30.05, which was scheduled for release yesterday.

The new Race Studio 2.30.06 can be downloaded here.

Also available are three new documents for new or improved features in Race Studio 2.

All are available on the same software download page.

Posted by Mike Jaynes at 02:39 PM

July 29, 2008

MyChron4 Update

Today's MyChron4 firmware update addresses two issues:

Please download MyChron4 firmware version 35.57.07 here.

Posted by Mike Jaynes at 01:25 PM

July 28, 2008

MXL GPS Update

The MXL firmware has been updated to include a new GPS firmware (v35.17) which addresses a bug, that under certain curcumstances would cause missed GPS lap times. It is recommended that all MXL GPS customers update to the latest 14.86.33g firmware. The new firmware can be downloaded here.

Posted by Mike Jaynes at 08:30 PM

July 18, 2008

MyChron4 Firmware Update

This version 31.55.07 is the first official US release to add GPS lap timing functionality, and addresses some other issues.

It is recommended that all MyChron4 be updated to this most current firmware, even if GPS and GPS lap timing is not used. The firmware can be downloaded here. You can grab the most recent version of Race Studio 2 at that same link as well.

Posted by Mike Jaynes at 12:33 AM

July 15, 2008

Race Studio 2 Update

Race Studio 2 goes to version 2.30.04 today with the following improvements:

The new Race Studio 2.30.04 can be downloaded here.

Posted by Mike Jaynes at 03:37 PM

MXL Firmware Update

MXL firmware update v14.86.33 gas gone public and offers the following improvements:

You can download the new MXL firmware, and revision notes here.

Posted by Mike Jaynes at 03:15 PM

June 06, 2008

MyChron4 GPS Lap Timing

GPS automatic lap timing has been enabled in this first public release of new MyChron4 and GPS firmware. You can download the update along with the GPS lap timing manual below. Feedback is appreciated.

Download the new firmware, and well as the MyChron4 GPS lap time manual.

MyChron Mike

Posted by MyChron Mike at 01:46 PM

April 24, 2008

MyChron4 Update 31.55.06

Mychron4 Front Gr450
A new MyChron4 firmware is available for download. The update contains a bug fix for the RPM Peak Hold function that didn't work properly in some High Stall Clutch applications. Also fixed was a bug that under very rare circumstances would create a problem with data memory. The Dutch language package has been updated, and lastly the firmware updates the MyChron4 data key to version 33.27, which addresses some issues with firmware upgrades for old firmware versions. It is recommended that all MyChron4 owners upgrade.

Click here to download this update. Data key required for firmware upgrade.

Posted by Mike Jaynes at 11:17 AM

January 18, 2008

MyChron4 Update

M4_58h.jpgThere's a new firmware release today for the MyChron4. The new firmware addresses the following:

Click here to download this update. Data key required for firmware upgrade.

Posted by Mike Jaynes at 12:51 PM

January 11, 2008

Race Studio 2 Update with Vista Drivers

Race Studio 2.22.07

Race Studio 2 reaches version 2.22.07 with some minor language and bug fixes. Most significant is a new USB driver with better Windows Vista (32-bit) support. You can download the new version and related release notes here.

Posted by Mike Jaynes at 02:55 PM

December 20, 2007

MXL GPS Lap Times

MXL firmware version v14.86.23 was released today with some significant improvements.

GPS Lap and Split Times
Finally out of beta, beacon-less lap timing has arrived. GPS lap and split timing is now possible with this new firmware version. The MXL now has a GPS lap/spilt setup page, which allows you to drive around the track and press a button where you want the lap and split times to be. The GPS module for the MXL has a 50 track memory, so once a lap/split configuration is done for a track, you won't have to do it again. It will "know" where you are, just start driving.

Gpsglobe The GPS Lap Time User Manual can be downloaded here. While the MXL v14.86.23 firmware can be downloaded here. Please note that it is important to have the GPS module connected to the MXL during the firmware update, as the GPS module is also updated.

The GPS Lap Manual also contains some brief notes on a beta software called GPS Manager. While it is beta, this software allows you to export GPS lap/split configurations from the GPS module, and send the config to another GPS module or vehicle. This is important for teams who need to overlay data and do not want the time shift of different GPS beacon locations. This software will also allow you to name, remove, store, share, and add notes to the GPS lap/split config file. The GPS Manager beta can be downloaded here.

MXL Memory Key
Mxl Memkey 250 This firmware also adds support for a new MXL Memory Key due out in January. Using a similar CAN/USB data key to our MyChron4 product, the new MXL Memory Key connects anywhere to MXL expansion CAN-bus and all data is recorded directly to the Memory Key, while simultaneously recording the MXL memory. The Memory Key contains 32MB of memory. The Memory Key has been extensively tested and is very robust. It is hot swappable, it can be removed or connected while the car is running and moved between cars. Because the Memory Key is also a USB device, you no longer have to bring the lap top out to the car, rather just take the key from the car and plug it into your USB port to download from the key.

Online Vref Value
All AiM systems for the past 11 years have used a 4.5V reference for analog channels, earlier this year, the MXL was moved to a more standard 5.0V reference voltage. The software intelligently manages this change and is transparent to the user. However, when creating custom sensors with the Custom Sensor function, knowing the reference voltage is often required. With the added Online Vref Value, you no longer need to bring out the multimeter to determine whether your MXL is a 4.5V or 5.0V system.

Posted by Mike Jaynes at 12:47 PM

December 19, 2007

Race Studio 2.22.06

Race Studio 2.22.06 Image

Race Studio 2 revs to v2.22.06 with the following changes:

Race Studio Configuration

1. New main interface

• In the main window there are new buttons corresponding to the main software functions.

• The “AIM system manager” button opens a pane where the user can select the system and go to the corresponding configuration window.

• Download and other convenient buttons added.

2. Data downloading from Memory key.

• Managment of MXL CAN/USB Memory Key.

3. Updated Japanese language database.

4. Fixed download bug that caused GPS data to be shown only for the first lap of a run.

Race Studio Analysis

1. Updated Japanese language database.


Download Race Studio 2.22.06 here.

Posted by Mike Jaynes at 01:45 PM

December 13, 2007

MyChron4 & DaVid Updates

The MyChron4 firmware reaches v31.50 today with a couple of small changes to the v31.49 released last week.

• Fixed bug on Japanese strings visualization to Euro version
• Added language Portuguese management to Euro version
• Added “Direct Drive” option in MyChron4 USA version for Oval Race Mode

The last item, added the "Direct Drive" option to the oval mode, is really a convenience item, as both low-stall and direct drive are treated the same by the MyChron4.

The DaVid standalone system got its first update in about a year and half. Firmware v17.08 improved Speed channel management on TG Dash and MyChron 3 displays.

Click here to go to the MyChron4 download page.

Click here to go to the DaVid firmware download page.

Posted by Mike Jaynes at 01:26 PM

December 11, 2007

Software and Firmware Updates

Our site was updated today with a few software and firmware updates released recently.

MyChron4
Firmware updated to v31.49.04

MyChron3 Dash
Firmware updated to v15.07

Race Studio 2
Software updated to v2.22.05

Latest software and firmware updates are always recommended.

Posted by Mike Jaynes at 08:26 PM

October 12, 2007

Updates; MXL, RS2, XG Log

Updates are now available for the MXL, the MyChron3 XG Log, and a new Race Studio 2 version, taking it to v2.22.03

Download Page

Posted by Mike Jaynes at 08:33 PM

August 03, 2007

Race Studio 2 Update +Vista

Race Studio 2.21.31 is now available for download. This version adds management for a new EVO3 Pista data logger. It adds still more ECU support for:

• Ford Focus PZEV 2003-4
• Ford Focus 2005-07
• Electromotive TECgt (beta testing only)
• Lotus Elise/Exige
• Ductati 1098

It also improves the ECU protocols for the Hondata K-Pro, Ducati Energia, and the Ford Mustang 05-07. Also to avoid some issues under Race Studio Analysis, some special characters cannot be used in "Channel name" field. These keys will be replaced by an " _ " (underscore).

Vistaicon

Also available today is Race Studio Version 2.22.02 beta, which adds support for Windows Vista.

Posted by Mike Jaynes at 08:25 PM | Comments (0)

July 25, 2007

New, Old MXL Firmware

MXL firmware version 14.83 is now available for download. For some reason, this version was completed in May but kept secret until now. The revisions are minor.

Posted by Mike Jaynes at 08:55 PM | Comments (0)

June 29, 2007

MyChron4 Firmware Update

Mc4 Loop Display

A new MyChron4 firmware is available that has some significant improvements. The update also applies new firmware to any connected e-box, GPS or lambda controller. You can download the firmware here, as well as the complete version history in PDF.

Posted by Mike Jaynes at 10:12 PM

June 15, 2007

Electromotive TEC3

TEC3

The much requested Electromotive TEC3 ECU is now fully supported! You can now connect your MXL, MyChron3 XG Log, or DaVid system directly to your Electromotive TEC3 ECU. The TEC3 streams up to 28 channels of data via direct serial connection. Having such an ECU connection scores nearly all engine data, and also frees up analog inputs for other input types like; steering position, shock travel/velocities, additional temps, additional pressures, infrared tire temps, and more. Connecting the TEC3 is as simple as connecting two wires.

Posted by Mike Jaynes at 07:54 AM | Comments (0)

Hondata ECU Conection

Hondata

The Hondata protocol is now out of beta and working great! You can now connect your MXL, MyChron3 XG Log, or DaVid system directly to your Hondata KPro ECU and receive up to 23 channels of data from the ECU. Having such an ECU connection also frees up analog inputs for other input types like; steering position, shock travel/velocities, additional temps, additional pressures, infrared tire temps, and more. The KPro connection requires an inline circuit between the ECU and AiM dash/logger. The connection is available now for $75 USD. --Update Nov. 29th, 2007 - Works with model PRB KPro.

Posted by Mike Jaynes at 02:26 AM | Comments (0)

Hondata ECU Conection

Hondata

The Hondata protocol is now out of beta and working great! You can now connect your MXL, MyChron3 XG Log, or DaVid system directly to your Hondata KPro ECU and receive up to 23 channels of data from the ECU. Having such an ECU connection also frees up analog inputs for other input types like; steering position, shock travel/velocities, additional temps, additional pressures, infrared tire temps, and more. The KPro connection requires an inline circuit between the ECU and AiM dash/logger. The connection is available now for $75 USD. --Update Nov. 29th, 2007 - Works with model PRB KPro.

Posted by Mike Jaynes at 02:26 AM | Comments (0)

June 14, 2007

RS2 Vista Update

Vistadavid 450

A Vista compatible update to Race Studio 2 is coming real soon, perhaps even ahead of our July schedule. The above screen capture shows the DaVid video configuration screen, which was otherwise impossible in Vista. There is still some testing to do, including some backwards compatibility testing with Win XP and Win 98, but the progress is looking good.

Posted by Mike Jaynes at 06:15 PM | Comments (0)

June 05, 2007

Snap On, Snap Off

Snaponoff

Due to the beacon shift function not working in the current version of Race Studio 2 (I was told this will be fixed in the next release), I had my first go at making a screencast with Camtasia this morning to illustrate to a customer how the snap on/off feature works and how it can be used to accomplish the same thing.

Beyond the temporary shift of data for alignment purposes, there are many other uses for this feature, and from my weekends at the race track, very few know about this feature. Other uses come from wanting to line up linearized data based on something other than time or distance, brake pressures, and steering angle for example.

In any case, this 35 second full screen video shows the basics of the Snap ON/OFF feature and how to turn it on and off.

Michael Jaynes

Posted by Mike Jaynes at 10:31 PM | Comments (0)

June 04, 2007

Race Studio 2.21.29

RS2.gif Race Studio 2, version 2.21.29 in now available. Complete release notes are forthcoming, a partial list of changes include:

Race Studio Configuration

1. Added ECU management: Hondata K-PRO (AIM interface circuit needed)
2. Added ECU management: Walbro HPUH1 (Formula SAE)
3. Fixed bug on AUX 1-2-3-4 channels (ECU Nira I3+)
4. Fixed bug on Oilp and Vbatt channels (ECU Marelli Custom)
5. Inserted ABS_Alarm channel (ECU Mazda MX5)
6. Inserted AutoDiagnose error signal channel on default configuration for MXL Plug and Play Kit for Yamaha R1-R6
7. From now on, MXL/EVO3Pro data download software will remember driver and vehicle name associating it to the last data download with the same instrument
8. In the "Online window" it is now possible to show milliVolt (V/1000) values measures for analog sensors
9. Added visor management on EVO3 Pro systems
10. From now on, on MXL/EVO3Pro systems, the configuration software allows the insertion of top and bottom scale values with the same decimal figures chosen within the units field.
11. Fixed bug in the online window. The milliVolt value is now correctly shown only for meaningful channels.
12. Fixed ECT channel management on Suzuki GSXR1000 K7

Race Studio Analysis

- No changes since last release

Posted by Mike Jaynes at 06:49 PM | Comments (0)

May 08, 2007

Even More ECU Support

Clearly, one of our greatest strengths is our systems' ability to connect directly to your car or motorcycle's ECU — and therefore record and monitor the ECU data in real time. We currently support more ECU's than anyone in our industry, many more! These ECU connection are often as simple as connecting two wires, or sometimes just one. Over this 2-wire connection streams 10, 20, 30, even up to 100 channels of data, good high-speed data. As most of our customers are racers, we have avoided OBDII communication because it's simply not fast enough. Where we have used a connection at the OBDII port, is with some of the OEM protocols; Mazda, Nissan, Audi, VW, Porsche, and BMW. Here, we simply use the OBDII port to gain easy access to the cars CAN-bus, where we can simply "listen" to the messages flying around the vehicles electronic system, and record the channels we are interested in. While we could develop a OBDII system to communicate with nearly every vehicles diagnostic system, the quality and data rate would be compromised.

Just added ECU support:
Hydra EMS Nemesis
Performance Electronics ECU-1
Magnetti Marelli Toyota A
Nissan 350Z (OEM)

ECU's to soon be supported:
Electromotive TEC³
Hondata KPro
MicroTech Systems
...and more!

Posted by Mike Jaynes at 06:36 AM | Comments (0)

May 07, 2007

Windows Vista

WinVista One of the most common tech questions rolling in, is about support for Windows Vista. Officially, Windows Vista is not yet supported. Full support is expected in July, a couple months away. Our DragAnalyzer software seem to be OK running under Vista, though driver installation requires a little more work than in XP. Race Studio 2, on the other hand, is a mixed bag. Most cannot get it successfully installed and running. The DaVid video configuration is surely an issue. Our technicians here will update to Windows Vista about the same time as the Race Studio 2 release. Until then, our support for Windows Vista is VERY limited.

Posted by Mike Jaynes at 11:15 PM | Comments (0)

Race Studio 2 Update

RS2.gifRace Studio 2 reached version 2.21.25 today. Here in the USA, this is a combined update of v2.21.24 and .25. This release includes several bug fixes and improvements. It also adds support for four new ECU's; the HydraEMS Nemesis 2 ECU, the stock Nissan 350Z ECU, Marelli Toyota A, and Performance Electronics ECU-1. Continue reading for update details.

Race Studio Configuration
1. On MXL and EVO3 Pro systems, changing the ECU type will maintain the master channels settings
2. Added clock management on MXL / EVO3 Pro systems
3. Added a Shift light signal with threshold management to the available output signal pool
4. Updated Japanese language
5. On MXL and EVO3 Pro systems, in the “Online” window channels are ordered as shown in the Configuration Panel
6. On MXL and EVO3 Pro systems, the “Online” window can be resized
7. Improved data verification while downloading tests
8. Fixed bug – downloading some test can lead to a queued “ghost lap”
9. Fixed bug – Before CAN line identification, sometimes it was necessary to transmit a configuration with no expansion modules connected; lambda probes or David.
10. Fixed bug on maximum allowable frequency on ECU channels
11. Fixed bug on resetting the rpm values to default on David Standalone system
12. Added ECU management: HydraEMS Nemesis
13. Added ECU management: Nissan 350Z
14. Returned 100hz channels sampling frequency is available (on Mazda MX5 ECU)
15. Added ECU management: Marelli Toyota_A for EVO3 Pro
16. Added ECU management: Performance Electronics PE-ECU_1

Race Studio Analysis
1. In the Laps history bar, disabled laps are hidden in “snap on” mode
2. Fixed bug on calculating split times in the split time window
3. Fixed bug that could generate a software crash while opening or closing a .drk file keeping the engine analysis window open
4. Fixed bug in XY graph profiles management
5. Fixed software/firmware version string in the advanced info test window
6. Added a new algorythm to realign GPS data
7. Fixed indexing procedure and export of XML (Google KML) files
8. Improved filters management in Channels Optimization
9. Fixed bug on final time calculation in Time Compare function
10. Fixed cursor misalignment between map and time plot while zoomed

Posted by Mike Jaynes at 06:00 PM | Comments (0)

February 26, 2007

Updates; RS2, MyChron4, & MXL

Late last week we finished three updates.

RS2.gif Race Studio 2 has gone to version 2.21.22, which adds additional ECU support, and includes a few general improvements as well as minor bug fixes to both the configuration software and analysis software. This release also continues GPS analysis improvements. This download also includes sample GPS data from Daytona.

M4_58h.jpgThe MyChron4 firmware update includes better management of the data key and adds zero configuration support to the forthcoming GPS module, as well as support for the LCU-One lambda controller. Also snuck in is a divide by two (/2) Engine RPM setting, bringing support to some two cylinder, single coil applications.

mxl_58h.jpgThe, also new, MXL firmware update (14.81) is the first non-beta version to include zero configuration support for the new GPS module. The most significant improvement is run based downloads. This means if multiple sessions are run without a download, each session will produce it's own download file when downloaded. Whereas previously, multiple sessions where combined into one download and file. Version 14.81 also offers more robust CAN management. This update will also update any connected LCU-one to a new version with minor improvements. Lastly, v14.81 contains the first release of MXL QM (Quarter Mile) support for a forthcoming drag race offering. Important note, this firmware requires Race Studio v2.21.21 or later.

All updates are suggested for all customers.

Posted by Mike Jaynes at 11:32 PM | Comments (0) | TrackBack

January 19, 2007

New Race Studio 2 Version 2.21.18

rs2GPS.jpg


Race Studio 2 reaches version 2.21.18. This update adds additional ECU support, fixes bugs and offers general improvements. Also added is 3D GPS visualization for the upcoming GPS add-on module. See release notes for v2.21.16-18.

Release Notes | Download

Posted by Mike Jaynes at 06:42 PM | Comments (1)

September 15, 2006

Race Studio 2 Software Update version 2.21.11

images_update.jpgUpdate September 15th, 11:00 AM PST. In error, the link to v2.21.11 pointed to v2.21.10, it now correctly points to v2.21.11.

An update to Race Studio has been posted. Race Studio version 2.21.11 has some fixes to previous versions.

Click here to download the update and read the release notes.

Release notes:

1. Fixed bug for which Online function didn't work for DaVid systems.
2. Fixed bug for which Online window always showed the message "Configuration not ok" for MXL systems.

Posted by aimsports || erik at 06:00 PM | Comments (0)

September 01, 2006

Race Studio 2 Software Update

images_update.jpgAn update to Race Studio has been posted. Race Studio version 2.21.10 features a number of improvements and fixes to previous versions.

Click here to download the update and read the release notes.

Release notes:

Race Studio Configuration

1. Fixed bug for which, creating a new configuration for some acquisition systems, speeds units were shown in place of pressure ones.
2. Executable resources have been modified in order to have the correct icon set as default for the executable.
3. Fixed bug for which the unit temperature was fixed in MXL configuration once set at the beginning.
4. The firmup is no more launched from RS2, a message informing user for the need of a firmup used instead.
5. Dutch language has been updated for the Lambda Configurator.
6. Fixed bug for which, downloading data from MXL systems, some channels showed zero values.

Race Studio Analysis

1. - Engine Analysis: fixed bug for which the y axes for power and torque showed different values, added a table numeric representation of torque and power, fixed problem for which the MS Excel file export wasn't possible.
2. - Added 4 values for practice and qualifying for test type in drk file properties.
3. - Fixed bug for which some wrong values in drk measurements could arise after deletion of math channels.
4. - Fixed bug for which an application crash could arise while opening a drk file with wrong run values in laps structures.
5. - Improved the management of profiles, the possibility of storing the settings of a channel (top and bottom of scale, alarms) for any further opening of other files.
6. - Histogram: fixed bug in the beans number management, fixed bug that made impossible to get the percentage histogram.
7. - Fixed bug with drk channels color management.
8. - Added possibility to manage the colors of the map and of split in measures plot.
9. - Fixed bug for which a second drk loaded could misalign the zoom level of both files and create errors in time compare.
10. - Fixed bug for which the icon's tooltips in split times toolbar were wrong.
11. - Split times: fixed bug for which in some cases the split value was wrongly computed and shown as "-1#IO", creating errors in best rolling lap value.
12. - Fixed bug for which, clicking the zoom icon in the toolbar and then clicking on the map, some wrong intervals were marked on measures plot.

Posted by aimsports || erik at 09:02 PM | Comments (0)

August 31, 2006

Important MXL Firmware Update

images_update.jpgIf you are using an MXL with a DaVid Slave, today's firmware update (MXL Firmware version 14.61) is important. This update addresses an issue with RPM display on MXLs connected to DaVid Slave units.
Click here to download the update and read the release notes.

Posted by aimsports || erik at 02:55 PM | Comments (0)

August 04, 2006

MyChron4 Firmware Update Adds Support for eBox Gold

images_update.jpgFirmware update version 32.16 for MyChron4 adds support for the newly released MyChron4 eBox Gold.

Download the update on the MyChron4 downloads page. Be sure to apply this update to the MyChron4 before connecting the eBox.

Also released today was an update to Race Studio. See the release notes for more information. Download this update from the Race Studio downloads page.

Posted by aimsports || erik at 08:14 PM | Comments (0)

August 03, 2006

MyChron TG LOG Firmware Update

images_update.jpgToday we released a firmware update (version 19.16) for MyChron TG LOG data loggers. This update adds a 1/3 factor to the RPM input.
Click here to download the update and read the release notes.

Posted by aimsports || erik at 06:21 PM | Comments (0)

July 28, 2006

Race Studio Software Update

Race Studio was updated today to version 2.21.08, click here to download the free update.

Release notes for Race Studio version 2.21.08

1.Fixed bug from the last release for which instead of the right strips the line "S0002:[Microsoft][Driver ODBC Microsoft..." used to appear.

Release notes for Race Studio version 2.21.07 (released yesterday)

1. Added new languages management through dll.
2. Fixed bug for which the total acquisition frequency was not updated after making a channel able or unable.
3. Fixed bug on the visualization of the panels with the speed parameters for MXL and DaVid systems
4. Added possibility to download and save data from a USB key just clicking on "download selected"
5. Fixed bug of the previous version for which the selected language used to be automatically reset in English or wasn't consistent with RSA
6. Fixed bug on the MX-5 channels visualization for XG-Log
7. Replaced the ABS speed channel management for MXL, where each of the two speed channels must be set as ABS speed channel
8. Fixed the language management (the previous version didn't work properly if
italian or english languages were selected, other languages worked properly)

Posted by aimsports || erik at 04:23 PM | Comments (0)

July 21, 2006

Race Studio and MXL Firmware updates

images_update.jpg
Today we posted a new version of Race Studio (2.21.06) and a firmware update for MXL (14.60). Geared mostly toward auto racers using MXL (all versions) and DaVid, both updates address a number of new features.


Posted by aimsports || erik at 05:20 PM | Comments (0)

June 05, 2006

MyChron4 "Freeze-Fix" Update *Updated June 5th*

hold-rpm-peak.gifWe have identified a bug in the MyChron4 firmware that can cause the screen to freeze under certain circumstances, though the data continues to record. The quick-fix is to turn off the 'Hold Peak RPM' feature, the best solution is to update the MyChron4 firmware, which requires the data key.

1) To turn off the RPM Hold feature:

Press the Menu button on the MyChron4
Select 'Control Panel', press 'Enter'
Select 'RPM Setup' (default), press 'Enter'
Select 'Hold Peak RPM', press enter until you see "OFF"
(see screen shots at right)

2) To fix the problem for good, download the firmware update and load it into your MyChron4 with the Data Key. Download the update from the MyChron4 downloads page. You should read the release notes before use.

This firmware update also fixes some issues with the "Best Rolling" and Split features. The split feature now works correctly for tracks with 3 or more magnetic strips.

Posted by aimsports || erik at 12:07 PM | Comments (0)

February 21, 2006

Race Studio 2 Software Update

Race Studio version 2.20.18 was released today, providing a number of fixes and updates for users. This update is a free download for all users, and provides the complete software package. Click here to go to the Race Studio downloads page.

If you've never used Race Studio before, it's worth checking out. Be sure to have the download cable for your gauge, or borrow one from a friend. Race Studio helps you manage your gauge, and, most importantly, it analyzes the data collected by your gauge so you can see what you and your vehicle are doing on the track.

Posted by aimsports || erik at 02:53 PM | Comments (0)